Manual / Getting Started
Common Setups
Four ways to build a followspot system with OpenFollow, from one operator to several stations. Each starts from a station set up with the Quick Start.
| Setup | Stations | Operators | Like |
|---|---|---|---|
| One station, one operator | 1 | 1, one marker | A single followspot |
| One station, several operators | 1 | Several, one marker each | Several followspots operated from one place |
| Several stations, several operators | Several | One per station | Several followspots operated from separate places |
| Designer View | One extra | None | A monitor at FOH that shows every marker |
Two rules hold in every setup:
- One station controls each marker. If two stations set the same marker to View & Control, both send it, receivers see it jump, and Marker Control & Visibility marks the row as a Conflict.
- Marker IDs are what the console sees. Patch the console to the marker ID, not to a station or an operator.
One station, one operator
One operator follows one performer: the classic followspot. A new station is already set up this way.
- CameraOne feed of the stage.
- StationOne gamepad drives marker 1.
- ConsoleReceives marker 1 over PSN.
- Set up the station with the Quick Start. Marker 1 is set to View & Control from the first boot.
- Give marker 1 a name under Markers & Zones → Marker Control & Visibility, such as the performer’s role.
- Plug in one USB-wired gamepad.
- Patch marker 1 on the console – see the guide for grandMA3, grandMA2, ETC Eos or ChamSys MagicQ.
One operator can also follow several performers in turn: add more markers set to View & Control and switch between them with the Next / Prev Marker buttons. That works when only one of them moves at a time. See Switching markers.
One station, several operators
Two or more operators share one station, one screen and one camera, each with a gamepad and a marker of their own.
- CameraOne feed of the stage.
- StationGamepad C1 drives marker 1, C2 marker 2, and so on.
- ConsoleReceives every marker over PSN.
- Under Markers & Zones → Marker Control & Visibility, set one marker per operator to View & Control, in the order the operators sit. C1 drives the first marker set to View & Control, C2 the second.
- Plug in one gamepad per operator. Each takes a slot by its USB socket, so label the sockets and keep each pad in its own.
- Open Input → Controller Slots and click Identify on each slot: the pad vibrates or lights where it can, and its marker card flashes on the Operator Screen, so every operator knows which marker is theirs.
- Patch every marker on the console.
Each marker is drawn in its catalog colour. With two or more gamepads, the D-Pad no longer switches markers, so nobody can take over another operator’s marker. A pad that drops out turns its marker card red; the marker stays where it was. See Controller Slots.
Use a large display: everyone works from the same screen.
Several stations, several operators
Each operator has a station, a display and a gamepad, usually in separate places. The stations can share one camera feed or use one camera each.
- CameraOne shared feed, or one per station.
- StationsStation A controls marker 1, station B marker 2.
- ConsoleReceives one PSN source per station.
- Set up every station with the Quick Start, all in one subnet. They find each other on their own and share one marker catalog.
- On each station, set its own marker to View & Control and the other operators’ markers to View. A new station controls marker 1, so change that on every station but one.
- Shared camera: calibrate one station with the Setup Wizard, then send the result to the others with Apply to all stations on Camera & Lens Calibration and on Grid (see Apply to all stations). Every station still selects the camera under Video Source. Check that the camera serves enough streams at once.
- One camera per station: calibrate every station on its own, all to the same Reference Point. Don’t use Apply to all stations here: it reaches every station on the network and would replace their calibration.
- Patch every marker on the console. A console sees each station as its own PSN source; on grandMA3, add one System per station.
Markers set to View appear dimmer and without a speed bar, so each operator sees the others without being able to move them. They arrive over PSN, so PSN input must stay on under Features (it is on by default).
Designer View
An extra station at FOH, with a display and no gamepad, shows every marker over the stage picture for the lighting designer or the director. It controls nothing and sends no positions.
- CameraThe shared feed, or a camera of its own.
- Operator stationsSend their markers over PSN.
- Designer ViewDraws every marker; sends nothing.
- Set up the station with the Quick Start in the same subnet as the operator stations, and connect a display at the production desk.
- Under Markers & Zones → Marker Control & Visibility, set every marker to View, marker 1 included. With nothing set to View & Control, the station sends no PSN.
- For the picture, select the operators’ camera and receive its calibration with Apply to all stations, or give the designer a camera of their own and calibrate it to the same Reference Point. A station with its own camera must not receive Apply to all stations from the others.
- Keep PSN input on under Features.
Don’t plug a gamepad into this station: it has no marker to drive.
Next steps
- Following a Performer – technique for the operators.
- Operator station – where to put the desks and screens.
- Networking & Security – subnets, multicast and IGMP snooping for several stations.